AC Repair & 32-Point Comprehensive Diagnostics
Engineered precision troubleshooting for inverter and fixed-speed split & window air conditioning systems. We isolate electrical failures, refrigerant starvation, and PCB micro-shorts down to the exact ohm and microfarad.
100% adjusted into final repair bill
Guaranteed same-day on-site slot
On replaced parts & workmanship
Common Faults We Diagnose & Rectify
Sudden drops in thermal comfort usually stem from discrete component degradations. Our technicians identify root causes within 20 minutes on site.
No Cooling / Warm Air Flow
The blower fan operates smoothly, but output air remains at room temperature. Usually triggered by compressor lockup, blown run capacitor, or zero suction line pressure.
Grinding, Rattling & Shaking
High-decibel screeching or rhythmic rattling indicates loose blower wheel bushings, degraded condenser fan motor bearings, or unseated compressor isolator feet.
Continuous MCB / Fuse Tripping
The distribution breaker trips within seconds of AC startup. Points to dead short circuits in the hermetic compressor motor, shorted IPM modules, or pinched control harnesses.
Severe Indoor Water Dripping
Water overflowing onto internal walls indicates clogged condensate siphon drains, cracked polystyrene drain pans, or evaporator ice-thaw cycles caused by low gas charge.
Cryptic Display Error Codes
Flashing digital codes (E1, E6, F3, CH05, etc.) signal communication bus timeouts, ambient thermistor drift, or inverted inverter motor phase sequencing.
Facing a Different Fault?
Our vans carry over 45 OEM diagnostic modules to evaluate unusual smells, remote unresponsiveness, or micro-vibrations across all Tier-1 brands.
The 32-Point Diagnostic Checklist
We don’t rely on guesswork or superficial checks. Our certified service engineers deploy digital instruments to assess electrical, mechanical, and thermodynamic systems systematically.
Electrical Dynamics
- check_circle Capacitor Microfarad (µF): Tested against rated factory variance (±5%).
- check_circle Compressor Winding Ohms: Common-Start-Run continuity verification.
- check_circle Input Voltage & Amp Draw: Running amp vs. locked rotor amps (LRA).
- check_circle Contactor Pitting: Inspection of relay contacts for carbon arcing.
Thermal & Gas
- check_circle Standing Gas Pressure: Gauge manifold psi check (R32 / R410A / R22).
- check_circle Suction & Discharge Delta: Delta-T air drop across cooling fins (8–12°C).
- check_circle Flare Joint Leak Sniffing: Electronic sensor sweeps over brass brassings.
- check_circle Expansion Valve Modulation: Testing for capillary blockage or frost.
Micro-Controller Logic
- check_circle Thermistor Resistance (kΩ): Ambient & pipe sensors at reference 25°C.
- check_circle IPM Dual-Inverter Transistors: DC bus voltage balance across phases.
- check_circle Comm Signal Pulses: Indoor-to-outdoor serial bus data integrity.
- check_circle Display Panel IR Sensor: Transmitter responsiveness and LED banks.
Airflow & Hydraulics
- check_circle Blower Motor RPM: Digital optical tachometer speed profiling.
- check_circle Condenser Fan Alignment: Blade balance and sleeve play checks.
- check_circle Condensate Gravity Gradient: Slope verification and bio-film check.
- check_circle Louver Stepper Motor: Flap gear alignment and sweep range.
Certified Diagnostic Equipment
Fluke True-RMS multimeters, Testo digital manifolds, and non-contact IR thermography cameras deployed on every vehicle.
Our Upfront Estimate Policy
No work begins until you approve an itemized digital quotation. If any component needs repair or replacement, the technician will walk you through the diagnosis and cost before touching a single screw.
32-Point Systematic Inspection
The field specialist isolates the root issue and generates a digital report on the Uni Finish field terminal.
Exact Itemized Pricing
You receive an exact SMS & WhatsApp breakdown of labor and genuine spare parts from our fixed catalog.
₹299 Completely Waived
When you approve the work, your initial ₹299 diagnostic fee is deducted 100% from your final service total.
Transparent Component Price Guidelines
We operate on standard rate matrices calibrated with OEM manufacturers. No marked-up spares or hidden surcharges.
Run Capacitors
Heavy-duty OEM dual or single capacitors (25µF to 60µF) for compressor start assist.
Thermistors & Probes
Indoor room temperature sensors & copper coil defrost probes (5kΩ to 15kΩ).
Magnetic Contactors
Heavy-duty outdoor compressor power switching relays rated up to 40A.
PCB Repairs / IC Rework
In-lab component repair, IPM bridge diode swaps, and micro-trace restorations.
Frequently Asked Questions
Everything you need to know about our diagnostic inspections and repair policies.
What if I choose not to repair after the diagnostic inspection? expand_more
How long does a typical AC repair take? expand_more
Are replaced spare parts covered under warranty? expand_more
Do you service inverter ACs and multi-split systems? expand_more
Specialized Sub-System Services
AC Compressor Repair
Direct terminal repairs, rotary compressor valve re-sealing, vibration pad replacements, and hermetic flush routines.
AC PCB Micro-Repair
In-lab SMD rework, power transformer swapping, micro-controller firmware resets, and IPM replacement for inverter units.
Gas Refill & Leak Test
High-pressure nitrogen pressure testing, copper brazing repairs, vacuum pump deep evacuation, and exact-gram refrigerant charging.
Restore Ice-Cold Cooling Today
Book our certified diagnostic engineer for ₹299. If you proceed with the repair, your inspection visit is 100% free.